Waste King Commercial Disposers

Waste King Commercial Garbage Disposer: 10000-3, 10 HP Three Phase

$4,965.00

Add to Cart:

Product Description

Two week lead time, mounting systems available at an additional charge, call for availability.

(Base unit shipping weight 272 lbs.)

Rough-In Dimensions with drain line connections
Cone Mounted Models

Model 10000-3, Three Phase

(Floor Mounted Unit)

Application

LARGE THROAT OPENING AND HIGH CAPACITY GRINDING COMPONENTS DESIGNED FOR QUICK, EFFICIENT DISPOSAL OF THE TOUGHEST LOADS

	Waste King® Exclusives
	•	Anti-Jam Swivel Impellers rotate out of the way of an impending jam, then fall back into grinding position, pulverizing waste particles
	•	Stainless Steel Undercutter Blade located beneath the grind ring snips fibrous and stringy waste into small particles making them less likely to clog drain lines
	•	Hush-Cushions® isolate the unit from metal to metal contact, significantly reducing noise level. Hush-Cushions® are specially compounded and designed to withstand vibration and tension, and have a built-in safety splash guard

	Features
	•	10 HP disposer, dual voltage
	•	Fan cooled motor with ball bearing construction, and integral overload protection
	•	Dynamically balanced for smooth, long wearing operation
	•	Hush Cushion® mounting connection for 6" cone or sink opening includes an auxiliary water inlet
	•	Cast iron grind chamber with directional feeder ridges
	•	Cast iron exit chamber with auxiliary water injection inlet
	•	10" Diameter heavy duty, cast stainless steel turntable
	•	3 Jam resistant, hardened stainless steel swivel impellers with tungsten carbide inserts
	•	6 Ripper bars integrated with turntable and hard face beaded edge for prolonged life
	•	Stainless steel undercutter blade
	•	Hard, tough, cast alloy grind ring with dual stage grinding action
	•	Lifetime particle size control by non-wearing exit slots
	•	Threaded adjustable stainless steel legs

Mounting Systems

Trough Mount Assembly (TM)	Basic Cone Assembly (B)	Dish Table Cone Assembly (DT)
#2540 8" Weld-in flange for models with 8" throat	18" Cone - 8" Throat with 2 Swirl Sprays	18" Cone - 8" Throat with 2 Swirl Sprays
		18" Cone Cover
		Scrap Ring/Guard

	Plumbing
	Models 10000-3 and 10000-3S are equipped with a drain outlet for connection to a conventional 3" trap. The trap may be connected to a 3" branch waste line running directly into a waste stack. We recommend a slope in the waste line of not less than 1/4" per foot. Limit the 3" drain line to a turn free run of 15', then connect to a 4" or 6" line or stack. Connect directly to waste line, not through a grease interceptor.

	Motor Data
	10000-3 or 10000-3S 60 cycle 3 Phase 10 HP 1740 RPM 208-240/440 volts 19.4/9.7 amps Bearing permanently lubricated. Manual reset overload protection in motor.

	NOTE: The legs can be cut shorter if the unit must be lower than the minimum shown for the screw adjustment. 2" clearance must be maintained beneath the motor for ventilation. For example, on a flat floor the model 10000-3 can be shortened by 1/2". If space between disposer and wall is insufficient to allow for installation of trap, waste line may have to be at an angle to the wall as shown. See disposer leg modification instructions.

	NOTE: Disposer assembly includes disposer, mountings, and drain outlet. Other items shown in gray are available in mounting systems or ordered separately. Installation should be made in accordance with local codes. All specifications subject to change without notice. Assembly should be installed in accordance with Waste King's printed installation instructions. * Items available through Waste King

	To Specifiers
	So that you may be assured of receiving the fine quality you expect when you specify a WASTE KING® FOOD WASTE REMOVAL SYSTEM, we include the following sample specification for your convenience: Food waste disposer shall be 10 HP, 60 cycle, 3 Phase, 208-220/440v. There shall be a rubber Hush Cushion® between the disposer and the cone or sink to eliminate metal to metal contact. Turntable shall be of stainless steel with jam-resistant swivel impellers of hardened stainless steel with Tungsten carbide inserts. Turntable shall have stainless steel cutting blade rotating below the exit slots. Grind ring shall be precision ground on all cutting surfaces and shall have non-wearing size controlled exit slots. Disposer shall have a totally enclosed, continuous duty, fan cooled motor with integral overload protection. Unit shall be Waste King® model 10000-3 or 10000-3S.

Details

Model: 10000-3, Three Phase
Manufactured by: Waste King Commercial

Reviews

There are currently no product reviews.
NOTE: Reviews may require prior approval before they will be displayed